產品簡介
美國Extec公司Labpress 40全自動鑲樣機EXTEC Labpress 40 - Fully Automatic Mounting PressAdvanced Automatic Mounting Press
公司簡介
我司是精密測試儀器代理商，為在中國獨家代理美國Thermo-Electron X-射線測厚儀及德國ROENTGENANALYTIK Compact eco系列X-射線測厚儀。此兩種儀器主要用于鍍層或涂層厚度的測量，而且特別適合于對微細表面積或超薄鍍層的測量。以下我們公司其他主要產品： 新加坡QTEST CIMS 特性阻抗測試儀 韓國Micro Pioneer XRF-2000系列測厚儀 美國Solar Metrology 太陽能薄膜電池厚度測量儀 日本KYORITSU WAK-水質離子測試包 美國WALCHEM（禾威）電鍍藥液自動添加系統 美國OMEGA 600SMD離子污染測試儀 美國UPA / VEECO非破壞性厚度測試儀 美國EXTEC研磨 / 拋光器材及消耗品 英國JENWAY分光光度計 美國Kocour庫侖測厚儀、侯氏槽、陰/陽極片、離心機等 德國SCAN-DIA研磨 / 拋光器材及消耗品 美國INNOV-X伊諾斯RoHS分析儀(手提式:XRF 6500，臺式:Ray-tek1800) 美國ECI電鍍藥液分析系統 美國DICKSON/DeltaTRAK/OMEGA溫濕度記錄儀 日本SHIMADZU(島津)分光光度計、X射線熒光分析儀 日本IWAKI工業用泵 韓國K-Mac ST4080-OSP 光學測厚儀 美國SPELLMA******??電源供應器 日本KETT磁感/渦流涂層測試儀 俄羅斯INTRON PTH-1/ITM-52手提式線路板孔銅測厚儀 美國RPS可焊性測試儀 美國UNITRON工業用顯微鏡系統及表面光滑度測試儀 美國EXTECH多用途萬用表 美國CECO板材厚度測試儀、銅箔剝離強度儀 一直致力于為PCB廠商，電鍍行業，科研機構，半導體生產等電子行業提供高性能的儀器和優質的售后服務。【shanghai yilang yiqi youxiangongsi】
展開
產品說明
美國Extec公司Labpress 40全自動鑲樣機
EXTEC ® Labpress 40 - Fully Automatic Mounting Press
Advanced Automatic Mounting Press for compression mounting of material samples in thermosetting resin mounts. Includes hydraulic pumping system.
Extec’s Labpress 40 is a new advanced Automatic Mounting Press for compression mounting of material samples in thermosetting resin mounts. The unit has an integral hydraulic pumping system to apply the correct pressure to a range of interchangeable molds.
The Labpress 40 is a compact unit with digital instrumentation for clear display of time and temperature. Both of these parameters can be set to give the required automatic molding cycle. The unit requires only single phase electrical power and a water supply. A water inlet and outlet are located on the rear panel.
The Labpress 40 features a compact lightweight design, integral hydraulic pressurizing system, interchangeable mold sizes in inch and metric diameters, quick and easy mold change.
The hydraulic pressurizing system is contained in the metal cabinet. It comprises a compact hydraulic pump and controller which applies pressure to a mold through an intermediate cylinder. The cylinder acts as an amplification stage so that pressure applied to the mold is adequate to mold all currently used compression mounting materials. A control valve is fitted below the front control panel and can be adjusted for molding a particular resin.
The Labpress 40 can be configured with 1"; 1 ¼"; 1 ½"; 25mm; 30mm; and 40mm mold assemblies.
- Mold Closure:
- Cap holding top piston, locks with bayonet fitting, sealing mold.
- Hydraulic Pressure Unit:
- Compact Hydraulic Pump and Controller to Adjust Pressure; (in bar) Intermediate cylinder moving lower piston out of mold. Pressure Safety Valve
- Molding Pressure:
- Up to 6000 psi (Mold 1.25")
- Heater Block:
- Incorporates 4/250 W Heater Cartridges with fuses for Overtemperature Protection.
- Temperature Controller:
- Temperature can be set up to 250° C or 480° F; K Type Thermocouple
- Timer:
- Digital Timer can be set to count down, 0-60 minutes.
- Cooling:
- Cooling water channels in heater block connected to supply through a solenoid water switch.
- Dimensions:
- Width: 14" (355mm)
- Depth: 16" (400mm)
- Height: 15" (380mm)
- Weight:
本頁產品地址：http://www.521uz.com/sell/show-937731.html
免責聲明：以上所展示的[
Labpress 40 全自動鑲樣機 ]信息由會員[
上海益朗儀器有限公司]自行提供，內容的真實性、準確性和合法性由發布會員負責。
[給覽網]對此不承擔任何責任。
友情提醒：為規避購買風險，建議您在購買相關產品前務必確認供應商資質及產品質量！
