MX100TP Aim-tti MX100TP三路可編程電源

產品/服務：MX100TP Aim-tti MX100TP三路可編程電源
型號：MX100TP
品牌：英國 aim-tti
單價：面議
更新日期：2024-09-19
有效期至：長期有效
瀏覽次數：1999

產品簡介

Aim-tti MX100TP三路可編程電源Bench/System DC Power Supply, Multi-Range, Digital Control Triple Outputs, 3 x 35V/3A 315W, USB, RS232, LAN & GPIB Interfaces...

產品詳細介紹

Aim-tti MX100TP三路可編程電源
Aim-tti MX100TP三路可編程電源
Aim-tti MX100TP三路可編程電源
Aim-tti MX100TP可編程直流穩壓電源：
Bench/System DC Power Supply, Multi-Range, Digital Control Triple Outputs, 3 x 35V/3A 315W, USB, RS232, LAN & GPIB Interfaces

Three high performance outputs each with full functionality
Range switching gives variable voltage/current combinations
Shared power mode provides double power from a single output
Low output noise and ripple via linear final regulation
High setting resolution of up to 1mV and 0.1mA
Variable OVP and OCP trips on all outputs
50 setting memories per output plus 50 linked memories
Selectable voltage tracking (isolated tracking)
Selectable current meter averaging
Switchable remote sense capability
Graphic LCD provides simultaneous output metering
Numeric or spin-wheel control of all parameters
Individual or combined output on/off control with
programmable delay sequencing.
3U half-rack case for bench or rack mounting
GPIB, RS-232, USB and LAN (LXI) interfaces (-P models)
Duplicate power & sense terminals at rear (-P models)

MX100T and MX100TP:

315 watts total power
Three outputs of equal power, each capable of 35V at 3A
Range switching provides up to 70 volts and up to 6 amps

Aim-tti MX100TP可編程直流穩壓電源：
The MX100T differs from most other triple output power supplies in having three outputs of equal power, each with the ability to provide 0 to 35V at 0 to 3A.

Each output features simultaneous high resolution metering, switchable remote sense, and an individual output switch.

Mixed-mode regulation To provide its impressive power density the MX series combines high frequency switch-mode pre-regulation with linear post-regulation to offer performance that comes close to that of an all-linear design.

Excellent line and load regulation is matched by low noise and good transient response.

Range switching and power control range combination chart

To increase its ability to match a variety of applications, each output has more than one range.

Outputs one and two can provide 16V/6A as an alternative to 35V/3A, while output three can provide 70V/1..

When higher power is required, outputs two and three can be combined internally to provide up to 210 watts as either 35V/6A or 70V/3A from a single output. Remote control for system applications

The MX100TP incorporates USB, RS232, GPIB and LXI compliant LAN interfaces.These provide full remote control and read-back capabilities and are supported by an IVI driver for high level language applications. Duplicate power and sense terminals are incorporated at the rear.The compact half-rack 3U size uses front input ventilation which enables vertical and horizontal stacking without the need for additional ventilation space. A 3U rack mount suitable for one or two units is available.
Aim-tti MX100TP可編程直流穩壓電源：

OUTPUT 1
Ranges	Range 1 - 0V to 35V at 1mA to 3A; Range 2 - 0V to 16V at 1mA to 6A
Operating Mode	Constant voltage or constant current with automatic cross-over and mode indication.
Voltage Setting	By direct numeric entry or quasi-analogue rotary wheel; resolution 1mV.
Current Setting	By direct numeric entry or quasi-analogue rotary wheel; resolution 1mA.
Setting Accuracy	Voltage - 0.05% of reading ± 3mV; Current - 0.3% of reading ± 3mA to 3A, 0.5% of reading ± 3mA to 6A
Setting Stores	Up to 50 set-ups can be saved and recalled via the keyboard (or the digital interfaces on MX100TP).
Load regulation	<0.01% +5mV (CV mode) for any load change using remote sense.
Line regulation	<0.01% +5mV (CV mode) for a 10% line voltage change.
Ripple & Noise	Typically <0.5mV rms, <5mV pk-pk, 1mV rms max. (20MHz bandwidth).
Transient Response	<100us to within 50mV of set level for 5% to 95% load change.
Over Voltage Trip	Settable 1V to 40V in 0.1V steps
Over Current Trip	Settable 0.1A to 7A in 0.01A steps
Sensing	Selectable local or remote sensing.

Aim-tti MX100TP可編程直流穩壓電源：

OUTPUT 2
Ranges	Range 1 - 0V to 35V at 1mA to 3A; Range 2 - 0V to 16V at 1mA to 6A Range 3 - 0V to 35V at 1mA to 6A* (available when output 3 is disabled)
Operating Mode	Constant voltage or constant current with automatic cross-over and mode indication.
Voltage Setting	By direct numeric entry or quasi-analogue rotary wheel; resolution 10mV.
Current Setting	By direct numeric entry or quasi-analogue rotary wheel; resolution 10mA.
Setting Accuracy	Voltage - 0.1% of reading ± 10mV; Current - 0.3% of reading ± 3mA to 3A, 0.5% of reading ± 3mA to 6A
Setting Stores	Up to 50 set-ups can be saved and recalled via the keyboard (or the digital interfaces on MX100TP).
Load regulation	<0.01% +5mV (CV mode) for any load change using remote sense.
Line regulation	<0.01% +5mV (CV mode) for a 10% line voltage change.
Ripple & Noise	Typically <0.5mV rms, <5mV pk-pk, 1mV rms max. (20MHz bandwidth).
Transient Response	<100us to within 50mV of set level for 5% to 95% load change.
Over Voltage Trip	Settable 1V to 40V in 0.1V steps
Over Current Trip	Settable 0.1A to 7A in 0.01A steps
Sensing	Selectable local or remote sensing.

OUTPUT 3
Ranges	Range 1 - 0V to 35V at 1mA to 3A; Range 2 - 0V to 70V at 1mA to 1. Range 3 - 0V to 70V at 1mA to 3A* (available when output 2 is disabled).
Operating Mode	Constant voltage or constant current with automatic cross-over and mode indication.
Voltage Setting	By direct numeric entry or quasi-analogue rotary wheel; resolution 10mV.
Current Setting	By direct numeric entry or quasi-analogue rotary wheel; resolution 1mA.
Setting Accuracy	Voltage - 0.1% of reading ± 10mV; Current - 0.3% of reading ± 3mA
Setting Stores	Up to 50 set-ups can be saved and recalled via the keyboard (or the digital interfaces on MX100TP).
Load regulation	<0.01% +5mV (CV mode) for any load change using remote sense.
Line regulation	<0.01% +5mV (CV mode) for a 10% line voltage change.
Ripple & Noise	Typically <0.5mV rms, <5mV pk-pk, 1mV rms max. (20MHz bandwidth). 70V range - typically <1mV rms, <10mV pk-pk, 1.5mV rms max.
Transient Response	<100us to within 50mV of set level for 5% to 95% load change.
Over Voltage Trip	Settable 1V to 80V in 0.1V steps
Over Current Trip	Settable 0.1A to 3. in 0.01A steps
Sensing	Selectable local or remote sensing.

Output Protection
External Voltage	Output will withstand forward voltages of up to 50V (O/Ps 1 and 2) or 80V (O/P 3). Reverse protection by diode clamp, 3A max.
Fault Trip	The output will be shut down if a trip conditions listed below occurs. OVP or OCP Exceeding over-voltage or over-current settings for the output.
Over Temperature	Monitors internal temperature rise to protect against excess ambient temperature or blocked ventilation slots.
Sense Error	Monitors the voltage between the remote sense terminals and output terminals to protect against mis-wiring.

Connection
Output Terminals	Universal 4mm safety binding posts on 19mm (0·75”) spacing at front. Screw terminals at rear (MX100TP only). Terminals can accept fixed shroud 4mm plugs, standard 4mm plugs, fork terminals and bare wires.
Sense Terminals	Sprung loaded screw-less terminals at front. Screw terminals at rear (MX100TP only).

OUTPUT ON/OFF SWITCHING
Individual On/Off	Individual keys for each output. On state indicated by key illumination.
Multi-On/Multi-Off	Separate keys enable any combination of outputs to be turned on or off either simultaneously (default) or with timed delays from 10ms and 20s. Delayed operation indicated by flashing key illumination.

Aim-tti MX100TP可編程直流穩壓電源：

VOLTAGE TRACKING
The power supply can be set so that the voltage of an output is automatically set equal to that of another output and tracks any changes.
Tracking Modes	None, V2 tracks V1, V3 track V2, V2 and V3 both track V1.

SETTING MEMORIES
Individual Output Memories:
No. of Stores	50 per output
Parameters Stored	Range, Set Volts, Set Current, OVP, OCP
linked Output Memories:
No. of Stores	50
Parameters Stored	Range, Set Volts, Set Current, OVP, OCP (for all three outputs)

METERING (each Output)
Meter Function	5 digit voltage and current meters (O/P 1), 4 digit voltage and current meters (O/Ps 2 & 3). Simultaneous display of actual and set values.
Meter Resolution	1mV/0.1mA (O/P 1), 10mV/1mA (O/Ps 2 & 3).
Meter Accuracy	As per setting accuracy (CV mode).
Additional Metering Functions	V x A Calculated power in watts. Resolution 0.01Ohms. Accuracy 0·5% ± 3 digits

Aim-tti MX100TP可編程直流穩壓電源：

DIGITAL BUS INTERFACES (MX100TP only)
The MX100TP offers full remote control and read-back using USB, RS-232, GPIB or LAN (compliant with LXI). All interfaces are at ground potential and opto-isolated from the output terminals.
RS-232	Standard 9-pin D connector.
USB	USB 2.0 connection (backwards compatible with USB 1.x). Operates as a virtual COM port.
GPIB (IEEE-488)	The interface conforms with IEEE-488.1 and IEEE-488.2.
Ethernet (LAN)	Standard 10/100 base-T hardware connection. ICMP and TCP/IP Protocol for connection to Local Area Network or direct connection to a single PC.
LXI Compliance	LAN interface is compliant with LXI core 2011. (LXI is the abbreviation for LAN eXtensions for Instrumentation).

DIGITAL PROGRAMMING PERFORMANCE (MX100TP only)

Programming Speed:

Command Delay

Typically <100ms between receiving the command terminator for a step voltage change at the instrument and the output beginning to change.

Output Response:

Range	Direction	90% Load	No Load	Direction	90% Load	No Load
16V/6A	Up	10ms	10ms	Down	10ms	350ms
35V/3A	Up	10ms	10ms	Down	35ms	550ms
35V/6A	Up	10ms	10ms	Down	20ms	550ms
70V/3A	Up	25ms	12ms	Down	60ms	600ms

The above figures are indicative only and will be affected by load capacitance.

Aim-tti MX100TP可編程直流穩壓電源：

DRIVER SOFTWARE SUPPLIED (MX100TP only)
IVI Driver	An IVI driver for Windows is supplied. This provides support for common applications such as LabView, LabWindows, HPVEE* etc.
USB Driver	An installation file is supplied which calls a standard Windows* USB driver.
* LabView and LabWindows are trademarks of National Instruments. * HPVEE (now Agilent VEE) is a trademark of Agilent Technologies. * USB interface is supported for Windows 2000, XP, Vista, 7 and 8 (including 64 bit versions). Windows is a trademark of Microsoft.

Aim-tti MX100TP可編程直流穩壓電源：

GENERAL SPECIFICATIONS
Input:
AC Input	110V to 240V AC ±10%, 50/60Hz. Installation Category II.
Input Power	500VA max.
Temperature & Environmental:
Operating Range	+5oC to +40oC, 20% to 80% RH
Storage Range	-40oC to + 70oC
Environmental	Indoor use at altitudes up to 2000m, Pollution Degree 2.
Cooling	Intelligent variable-speed fans.
Safety & EMC:
Safety	Complies with EN61010-1
EMC	Complies with EN61326
Physical:
Size	212 x 130 x 375mm (WxHxD) (half rack x 3U height)
Weight	4.8kg (MX100T); 4.9kg (MX100TP).
OPTIONS:
Rack Mount	19 inch rack mount for one or two power supplies.

如果您覺得“MX100TP Aim-tti MX100TP三路可編程電源”描述資料不夠齊全，請聯系我們獲取詳細資料。(聯系時請告訴我從給覽網看到的，我們將給您最大優惠！)
本頁鏈接：http://www.521uz.com/com_sdongjin/sell/itemid-7178732.html
已經有1999位訪客查看了本頁.

產品咨詢

* 詢價標題：
快捷提問：	(不用打字 “快捷提問”幫您忙！)
* 主要內容：	我希望在日前回復
公司名：
*聯系人：
*聯系電話：
電子郵箱：
QQ ：
* 驗證碼：

詢價標題
聯系人
電話
主要內容
驗證碼

521uz.com-欧美老妇xxxxx性开放,中字幕视频在线永久在线观看免费 ,国产亚洲婷婷香蕉久久精品 ,国产av无码专区亚洲版综合

MX100TP Aim-tti MX100TP三路可編程電源

Aim-tti MX100TP三路可編程電源Bench/System DC Power Supply, Multi-Range, Digital Control Triple Outputs, 3 x 35V/3A 315W, USB, RS232, LAN & GPIB Interfaces...

相關產品推薦

相關技術文章